Effects of printing angle and post-curing time on the color and translucency of 3D-printed temporary restoration

Basit Öğe Kaydı
dc.authoridTemizci, Tuğba/0000-0001-8212-6122
dc.authoridKölüş, Türkay/0000-0002-0840-7126
dc.contributor.authorTemizci, Tuğba
dc.contributor.authorKölüş, Türkay
dc.date.accessioned2025-01-12T17:20:19Z
dc.date.available2025-01-12T17:20:19Z
dc.date.issued2024
dc.departmentKMÜ, Ahmet Keleşoğlu Diş Hekimliği Fakültesi, Klinik Bilimler Bölümü
dc.description.abstractIn resins produced with a 3D printer, the printing parameters affect the properties of the restoration produced. This study examined the effect of the printing angle and post-curing time on the optical properties of temporary restorations. A total of 135 disk-shaped Formlabs temporary resins (10 x 2 mm) were produced at three different printing angles (0, 45, and 90 degrees) and post-cured for three different times (20, 40, and 60 min) (n = 15). Color and translucency measurements were taken for each group with a spectrophotometer (VITA Easyshade V). The Delta E values between printing angles and curing times influence each other. The highest color change was observed in the groups produced with a 90 degrees printing angle. Considering the post-curing times, the highest color change was observed in the groups cured for 40 min. Increasing the curing time from 20 to 40 min decreases the translucency, whereas further increasing the curing time does not significantly affect the translucency. In terms of the impact on the translucency caused by the printing angles, 0 degrees exhibited a lower translucency compared to other printing angles. During the 3D printing of temporary prostheses, both printing angles and post-curing times can affect their optical properties.
dc.identifier.citationTuğba Temizci, & Türkay Kölüş. (2024). Effects of printing angle and post-curing time on the color and translucency of 3D-printed temporary restoration. Biomimetics, 9(7), 420. https://doi.org/10.3390/biomimetics9070420
dc.identifier.doi10.3390/biomimetics9070420
dc.identifier.issn2313-7673
dc.identifier.issue7
dc.identifier.pmid39056861
dc.identifier.scopus2-s2.0-85199614575
dc.identifier.scopusqualityQ3
dc.identifier.urihttps://doi.org/10.3390/biomimetics9070420
dc.identifier.urihttps://hdl.handle.net/11492/10376
dc.identifier.volume9
dc.identifier.wosWOS:001276678900001
dc.identifier.wosqualityN/A
dc.indekslendigikaynakWeb of Sceince
dc.indekslendigikaynakScopus
dc.indekslendigikaynakPubMed
dc.institutionauthorTemizci, Tuğba
dc.institutionauthorKölüş, Türkay
dc.institutionauthoridTemizci, Tuğba/0000-0001-8212-6122
dc.institutionauthoridKölüş, Türkay/0000-0002-0840-7126
dc.language.isoen
dc.publisherMdpi
dc.relation.ispartofBiomimetics
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanı
dc.rightsinfo:eu-repo/semantics/openAccess
dc.subject3D printing
dc.subjectprinting angle
dc.subjectpost-curing time
dc.titleEffects of printing angle and post-curing time on the color and translucency of 3D-printed temporary restoration
dc.typeArticle

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim
İsim:
Tam Metin / Full Text.pdf
Boyut:
2.49 MB
Biçim:
Adobe Portable Document Format
İndir

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Klinik Bilimler Bölümü, Makale Koleksiyonu
PubMed İndeksli Yayın Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu